CST2466 英文版规格书下载 CST2466中文版下载
CST2466/CT2466E概述:
CST2466/CST2466E是2.1A H桥驱动芯片。较宽的输入电压2至11V。超低内阻280mΩ,CST2466/CST2466E提供SOP8和ESOP8两种封装。
CST2466/CST2466E为电动牙刷、摄像机、消费品、玩具和其他低电压或电池驱动的应用提供了集成电机驱动器控制, CST2466/CST2466E可提供高达2.1A的直流输出电流,使用2-11V的电机电源(VM)和2V-6V的设备电源(VCC),超低的RDS-on允许SOP-8包可用。CST2466/CST2466E具有PWM(INA、INB)输入接口。全套保护与过流保护、欠压闭锁和超温停机相结合。CST2466/CST2466E提供SOP8和ESOP8两种封。
The CST2466/CST2466E provides an integrated motor driver for cameras, consumer products, toys and other application with low-voltage or battery-powered motion control.The CST2466/CST2466E can supply up to 2.1A of output DC current. It operates on a motor power supply (VM) from 2 to 11V and a device power supply voltage (VCC) of 2V to 6V. Ultra- low R
DS-ON allows SOP-8 package available. The CST2466/CST2466E has a PWM (INA、INB) input interface. Full protections are integrated with over-current protection, under-voltage lockout and over-temperature shutdown.
CST2466/CST2466E特性:
H桥电机驱动器
-直流电机或其他负载
-低导通电阻:280mΩ
2.1A直流驱动电流最大值
独立的电机和逻辑电源
马达VM:2至11V
逻辑VCC:2V至6V
低待机电流小于2uA/Vm=Vcc= 5V
小包装和管脚
CST2466/CST2466E提供SOP8和ESOP8两种封装
不带散热片的8脚SOP8
带散热片的8脚ESOP8
8引脚防抖功能
电压锁定下的VCC
过电流护
过热关断
无需外围滤波电容
H-Bridge Motor Driver
DC Motor or Other Loads
Low On-Resistance :280mΩ
2.1-A Maximum DC Drive Current
Separate Motor and Logic Supply
Motor VM : 2 to 11V
Logic VCC : 2V to 6V
Low-Stand-by Current ≤ 2uA/VM=VCC=5V
Small Package and Footprint
8-Pin ESOP with Thermal PAD
8-Pin SOPProtection Features
VCC Under-voltage Lockout
Over-Current Protection
Thermal Shutdown
CST2466/CST2466E应用
电动牙刷、电锁
摄像机
数码单反透镜
消费品
玩具
机器人学
Electric toothbrush, Electric lock
Cameras
DSLR Lenses
Consumer Products
Toys
Robotics
CST2466/CST2466E PCB布局指导及典型应用电路图

The capacitor C1 connected between the GND and the VM pins must be located as close as possible to the CST2466/CST2466E chip. In different applications, C1(show as above) is recommended to use a 0.1uF in 3V applications; a 1uF is recommended for 4.5V applications; a 4.7uF is recommended for 6V applications; in 9.6V applications, it is recommended to use 22uF, all these capacitors should be SMD package. The connection between the negative pole of the capacitor and the GND terminal of the IC should be as short as possible. That is to say, the line route should not far away.
When the application board has capacitors while filtering for other chips that is far away from the CST2466/CST2466E, it need to place a small capacitor for CST2466/CST2466E.
The capacitor C3 preferably soldering to the motor poles instead of placing it on the PCB. When it is inconvenient to soldering on the motor poles, it can be mount on the PCB. The following diagram is the PCB layout reference .
CST2466 SOP8脚位图
CST2466E ESOP8脚位图

CST2466/CST2466E脚位定义
Pin number |
Pin name |
I/O |
Description |
1 |
VM |
-- |
Motor power supply |
2 |
OUTA |
O |
Motor drive output A |
3 |
OUTB |
O |
Motor drive output B |
4 |
GND |
-- |
Ground |
5 |
INB |
I |
Logic input B |
6 |
INA |
I |
Logic input A |
7 |
NC |
-- |
No connection |
8 |
VCC |
-- |
Logic power supply |